Because of its wide range of uses, good processing quality and high efficiency, the claw mill is very popular among users, but how to use it is very particular.
1. Use it correctly. Before starting the machine, perform a comprehensive inspection of the machine to confirm that the technical conditions of each part are good before starting up. After starting the machine, it should be idle for 1-2 minutes to confirm that there is no abnormality before the feeding operation. Feed the material should be uniform and pay attention to the adjustment of the feed amount. When processing corn and other grains, the feed amount is controlled by a regulating shutter to make it feed evenly. When processing bean cake, potato vine and other feeds, in order to facilitate the smashing, the bean cake must be broken first, and the large diameter of the zui is within 40mm; the potato vine is good to be chopped first, and the length is about 150mm; if crushing fresh potatoes, it must be Cut the block first and add an appropriate amount of water. At the same time, it is necessary to feed evenly to prevent the crusher from overloading and affecting the crushing quality. When using the powder bag to pick up the powder, when the powder in the bag reaches 1/3, the powder should be taken to avoid the temperature rise and the output is decreased. After the powder is taken, the bag should be vibrated to increase the gas permeability.
2. Ensure safe production. A protective barrier should be installed at the transmission. The operator should stand on the feeding side. Do not stand on both ends of the crusher. The cuffs of the clothes should be tied and the long hair should be inserted into the working cap. Before the material enters the hopper, the nails, stones and other debris should be removed to avoid damage to the machine. During the feeding process, if the material is blocked, do not clean it by hand. Stop the blockage. If the motor power is used, the power should be cut off before troubleshooting. Fireworks are prohibited at the work site, and it is forbidden to increase the output by increasing the speed.
3. Strengthen maintenance. When the machine is running, the bearing temperature should not exceed 40 degrees. If the bearing temperature continues to rise under normal working conditions, stop the machine immediately to find out the cause and eliminate the fault. After each operation, check whether the bolts in each part are loose, check whether the joints are in good condition, check whether the rotor is flexible, whether there is collision or noise, and check the wear of the teeth and the screen. In case of seriousness, it should be replaced in time. In addition, the lubricating oil should be regularly filled with lubricant.
1. Use it correctly. Before starting the machine, perform a comprehensive inspection of the machine to confirm that the technical conditions of each part are good before starting up. After starting the machine, it should be idle for 1-2 minutes to confirm that there is no abnormality before the feeding operation. Feed the material should be uniform and pay attention to the adjustment of the feed amount. When processing corn and other grains, the feed amount is controlled by a regulating shutter to make it feed evenly. When processing bean cake, potato vine and other feeds, in order to facilitate the smashing, the bean cake must be broken first, and the large diameter of the zui is within 40mm; the potato vine is good to be chopped first, and the length is about 150mm; if crushing fresh potatoes, it must be Cut the block first and add an appropriate amount of water. At the same time, it is necessary to feed evenly to prevent the crusher from overloading and affecting the crushing quality. When using the powder bag to pick up the powder, when the powder in the bag reaches 1/3, the powder should be taken to avoid the temperature rise and the output is decreased. After the powder is taken, the bag should be vibrated to increase the gas permeability.
2. Ensure safe production. A protective barrier should be installed at the transmission. The operator should stand on the feeding side. Do not stand on both ends of the crusher. The cuffs of the clothes should be tied and the long hair should be inserted into the working cap. Before the material enters the hopper, the nails, stones and other debris should be removed to avoid damage to the machine. During the feeding process, if the material is blocked, do not clean it by hand. Stop the blockage. If the motor power is used, the power should be cut off before troubleshooting. Fireworks are prohibited at the work site, and it is forbidden to increase the output by increasing the speed.
3. Strengthen maintenance. When the machine is running, the bearing temperature should not exceed 40 degrees. If the bearing temperature continues to rise under normal working conditions, stop the machine immediately to find out the cause and eliminate the fault. After each operation, check whether the bolts in each part are loose, check whether the joints are in good condition, check whether the rotor is flexible, whether there is collision or noise, and check the wear of the teeth and the screen. In case of seriousness, it should be replaced in time. In addition, the lubricating oil should be regularly filled with lubricant.
Mackerel Fish,Mackerel Frozen,Frozen Indian Mackerel,Frozen Pacific Mackerel
Zhoushan City Shuangying Aquatic Products Co., Ltd.  , https://www.shuangying-aquatic.com